OPS245 Lab 5

LVM Overview

A fixed partitioning setup works fine in many scenarios, but it lacks a lot of flexibility. Using LVM we can avoid the slow and complicated process you've seen in the previous lab, when we tried to extend the size of a partition.

Here's a comparison of how a physical storage device is used in the traditional setup (the one we've worked with in lab 4) and in LVM:

Traditional partitioning	LVM
Connect new physical device. Create partitions on the device. Format the partitions. Mount the formatted partitions.	Connect new physical device. Mark the device to be used as a physical volume in LVM. Add the physical volume to a volume group. Create a logical volume. Format the logical volume. Mount the logical volume.

Effectively a logical volume is equivalent to a partition, but it is not expected to be fixed in size, and it is not stuck on any specific hardware storage device.

Here's a graphical overview of how storage is managed in an LVM system:

In this example there are two drives (one 3GB and the other 1GB in size). They are both added to the LVM storage pool (called a volume group). Then two logical volumes are created using the space available in the volume group (one 1GB and the other 4GB in size).

Note that this kind of setup would be impossible to create with traditional partitioning. Since a partition must fit on one drive: you couldn't have a 4GB partition in this case.

Basic commands

If you followed the installation instructions from Lab 1: your server2 will be using LVM. Run the following commands on server2:

• vgs lists the volume groups on your system. You will likely never see more than one volume group on one machine. It shows you:
  1. The volume group name (you'll need it for some commands).
  2. The volume group size (the sum of the sizes of the physical volumes in this volume group).
  3. The amount of space in the volume group which has not been allocated to any logical volumes.
• pvs lists the physical volumes on your system. It shows:
  1. The device name of the physical volume. Note that it doesn't have to be an entire drive, it can be a partition. On server2 most of your 10GB drive is allocated to a partition (sda5) which is used as a physical volume.
  2. The volume group this physical volume is part of.
  3. The size of the physical volume.
  4. The amount of the space on this physical volume which is not allocated to any logical volumes.
• lvs lists the logical volumes on your system. It shows:
  1. The name of the logical volume.
  2. The volume group this logical volume is on.
  3. The size of this logical volume.
  4. It does not show how much space is used on this logical volume, you'll need to run the df -h command to see that.
• df -h does the same thing in an LVM system as in any other system, it shows you which devices you have mounted where and how much space is used on those devices. The device filenames for your logical volumes are in /dev/mapper and their names are a combination of:
  1. The name of the volume group, and
  2. The name of the logical volume.
• You can also use other familiar commands like blkid and lsblk.

Shrink home and create www

Most of the time what happens is you run out of space on a logical volume and you need to expand it. But since we only have one lab for LVM: we'll add a less common operation: shrinking a logical volume.

Assuming you already confirmed that your server2 is using LVM, run the following on server2:

The arguments for lvreduce are:

• -r shrinks the size of the filesystem first, then reduces the size of the logical volume.
• -L -1G instructs lvreduce to shrink the size by 1GB. You can also use a specific final size if you prefer.
• server2-vg/home is the name of the volume group, then a slash, then the name of the logical volume.

Note that it is not possible to shrink an ext4 filesystem (nor most other filesystem types) while it's mounted. So for example if you were logged in as a regular user (therefore using the /home filesystem) you would not be able to run this command successfully.

Now you have 1GB of unused space in your volume group. Use all the available space from server2-vg to create a logical volume named lv_www:

• Shrink the home LV
• Create www LV, fill it, expand it
• Fill www again, move all of it to new bigger PV
• Disconnect www from server2, move it to server3
• Expand home on server1